Technology

Installing A Water Filter? Follow These 8 Tips

Many believe that one can’t be fully certain that the water flowing from their taps is pollutant-free all the time. It’s said that investing in and installing a high-quality water filter is an excellent way to ensure that you and your household have round-the-proverbial clock access to safe and clean water.

If you want to know more info about installing a water filter properly in preparation for another home improvement project, the following tips may guide you. Read on to learn more about them.

1. Check Specifications Of The Filter

Before buying a water filter, review the specifications to ensure that the device you purchase is compatible with your property’s current plumbing configurations. Home water filters come in a variety of makes, shapes, and sizes. It’s said that the majority of them should be put inside or in a covered area to ensure their maximum performance.

Not every device is compatible with all kinds of home fittings. Therefore, always check that you get one that’s well-matched with your home before proceeding with any installation. Otherwise, you’ll not be able to make use of a water filter and may have to return it. Or worse, you’ll struggle with one that isn’t fitted correctly.

It’s advisable to get in touch with a plumbing expert if you’re unsure of your home’s sanitary structure and model.

2. Know The Basic Pipe Soldering Techniques

Set the device in the way recommended by the installation manual that came with it upon purchase. It’s also advised that you promptly install a shutdown valve on either end of the device. This avoids an overflow whenever the filter is changed. To accomplish this, you must first get acquainted with the different fundamental pipe soldering procedures.

To begin, wash the tube ends and shutdown valve areas. Brush these with wire wool. Following that, take out oxides from the inner layer of the pipes and valves with flux or a chemical being used in welding to link two materials. Finally, with a soldering iron and a torch, burn the iron into the pipe’s side, wherein the two parts will be linked.

3. Take Necessary Precaution When Cutting

When slicing into the primary water pipe, create a division big enough to fit the filtration system you’ve purchased. This can be accomplished with either a handsaw or a circular saw equipped with steel blades. Then use a steel file to polish off any sharp edges.

When slicing through metal, exercise caution at all times. Accidental cuts may lead to infections that may result in health concerns. Shield yourself against metal shards and debris that inadvertently get thrown around the project site by wearing safety glasses and a face shield.

4. Keep A Bucket Handy

Excess water supply may remain within the pipeline, thus placing a bucket underneath the spot you plan to cut would help capture any dripping liquid.

As an alternative, you may use a cloth to block and hold the existing gap. But it’s considered as not as effective as having a pail for you’ll need both your hands to function.

5. Turn On The Closest Faucet

The first stage in installing the filter is to shut off the primary water supply. However, because residential pipelines and tubing are often horizontally oriented, little air and water would probably stay inside.

Hence, to prevent spillage or leakage in the procedure, switch on the closest faucet to drain both air and water from the inner components. Make sure to have a container handy to catch the residual water to avoid any spillage.

6. Install A Pre-filter First

A pre-filter might be required to ensure the purest water quality attainable for your family possible. They’re believed to be used for two basic purposes. The first function is that they usually safeguard the main filtering medium from damage and deterioration.

Specific kinds of water filters may be harmed by certain impurities, like chemicals, particles, or microorganisms. Therefore, a pre-filter may be fitted to eliminate such potentially harmful pollutants before they reach the main filtering material.

Pre-filters’ second function is to eliminate impurities that the main filter is incapable of capturing and preventing from going to the water supply. This enables the filtering device as a whole to eliminate a broader spectrum of impurities. As a result, a higher-quality water supply may be attained compared to what you’re getting from just using the main filter alone.

In some cases, the pre-filter is utilized to take out the bigger pollutants to prevent them from clogging the main filtering device which extends the life of your main water filter.

7. Use A Pressure Valve

The water filter you buy will specify the greatest pressure it can withstand. If the pressure in your home is high, you may purchase a supplementary pressure-lowering valve and install it on the faucets. This can help your plumbing and water filter to perform properly and prolongs their usefulness.

Pressure lowering valves convert the strong water flow pressure to a more manageable level fit for your house’s fittings. They’re often positioned on the primary supply line. It’s important to remember that water pressure may vary at night. Pressure at nighttime might be higher depending on the local utility company or your area. Inspect your home’s water pressure at various periods of the day to see whether a pressure-lowering valve is required.

8. Connect The Filter Before Your Heater

The majority of water filters are said to be designed to operate on cool water and will be rendered ineffective if heated water is used. Therefore, even on maintenance, avoid running warm water on the filter since this may cause irreversible damage.

But you must also put the filter in a location where the water wouldn’t freeze during colder months. Extremely cold water could also cause damage to your new water filter.

Bottom Line

A water filter is said to be an excellent approach to safeguard your household from different waterborne contaminants and diseases. It’s a simple procedure to install with the use of the proper steps and tools. By following the abovementioned suggestions, you may prevent hassles when assembling your new filter.

Related Articles

Leave a Reply

Back to top button